屈变力，屈服强度，抗屈强度

[力]屈服强度；屈变力；抗屈强度

yield strengths───[力]屈服强度；屈变力；抗屈强度

field strength───[物][电子]场强；电场强度；磁场强度

field strengths───[物][电子]场强；电场强度；磁场强度

find strength───找到力量

full strength───满员；全强度

great strength───牛劲；强大的力量

green strength───[材]湿强度；生坯强度

in strength───大量地

real strength───实际强度

Residual stress concentration a notch depends on both notch geometry and yield strength of the material.───缺口根部的残余应力存在应力集中效应,应力集中值不仅取决于缺口几何形状而且和材料的屈服强度有关.

Oxgen precipitates ( useful for gettering ) can reduce the yield strength ( critical shear stress ) up to fivefole.───氧沉淀 ( 可用作吸杂 ) 会使屈服强度 ( 临界剪应力 ) 降低为五分之一.

Fatigue strength is less than static stress strength such as elasticity limit, yield strength.───疲劳强度低于弹性极限或屈服强度等静应力强度。

CuPTiRE anti - erosion hot rolling stripes are divided into two grades in yield strength : 295 MPa, 345 MPa.───09CuPTiRE耐大气腐蚀热轧钢板按屈服强度分为295MPa级和345MPa级两个级别.

The V - N microalloy steel with yield strength of 550 MPa is produced by EAF - CSP route.───目前,在EAF-CSP 流程中通过V -N 微合金化技术可成功生产屈服强度为550MPa的高强度低合金钢.

Good yield strength and tensile strength.───良好的屈服强度和抗拉强度。

FIG. 5 shows the average yield strength as a function of extrusion speed and location.───图5示出了平均屈服强度与挤压速度和位置的关系.

Dislocation strengthening and grain refinement strengthening makes coil 059 with the higher yield strength.───位错强化与晶粒细化强化是059板卷具有高屈服强度的原因.

The yield strength fy of reinforcement is used in design.───在设计中利用的是钢筋的屈服强度.

Yield strength elongation-strain corresponding to yield strength of material.───屈服强度伸长—对应于材料屈服强度的应变。

The yield strength ( σ0.2 ) , ultimate tensile strength ( σ b ) and elongation ( δ ) of A 356 - T 6 alloy were 240 MPa, 254.8 MPa and 1.16 % , respectively.───屈服强度 、 抗拉强度和伸长率分别为240MPa 、 254.8MPa和1.16%.

The creep rate was increased while the yield strength was reduced by anodic dissolution.───阳极电流不但使恒载荷下的不锈钢蠕变速度增加,而且使屈服强度下降.

The yield strength, tensile ratio and toughness are major quality indexes of steel pipe ( board ).───屈服强度 、 屈强比、韧性等是钢管 ( 板 ) 的主要质量指标,合理确定这些指标的数值有相当难度.

The results show that the steel has high yield strength and quality forming property.───结果表明,研制开发出的铌钛微合金化IF钢具有高的屈服强度和优良的成形性能.

Desirable properties for forming include low yield strength and high ductility.───令人满意的成形特性包含了低降伏应力和高延展性.