[机]离心浇铸

离心浇铸造法

centrifugal castings───[机]离心浇铸

central casting───(电影制片厂的)演员选派部，电影厂分派次要角色的部门

centrifugalising───离心

central castings───(电影制片厂的)演员选派部，电影厂分派次要角色的部门

centrifugal clutch───[机][车辆]离心式离合器

centrifugalization───n.离心分离作用；利用离心机而分离的物质

centrifugalizing───vt.使受离心作用

centrifugal clutches───[机][车辆]离心式离合器

continuous casting───全连铸；[冶]连续浇铸

Widely used for winding Al ( Cu, Steel ) foil. These rollers are produced by centrifugal casting methods.───箔材芯管套筒广泛应用于轧制铝 ( 铜 、 钢等 ),套筒采用离心铸造工艺生产.

A method of dynamic action was used during the solidification of the alloy in centrifugal casting.───在离心浇铸金属凝固过程中,采用动态效应的方法对以达到细化晶粒的目的.

Centrifugal casting, compact structure, free from pinhole porosity and slag, smooth surface and even wall thickness.───高速离心铸造, 组织致密, 无砂眼、夹渣, 表面光滑、壁厚均匀.

Technology of vertical centrifugal casting, the calculation for gate size and rotational speed mold were introduced.───介绍了立式离心铸造方法 、 浇口尺寸和铸型转速的计算.

Although there are a lot of the fabricating techniques of functionally gradient material (FGM), the centrifugal casting method is more effective, cheaper and easier to operate.───虽然梯度功能材料的制备方法很多，但效率较高、成本较低、操作较简单的方法是离心铸造法。

Technology for shaped castings in vertical centrifugal casting, including design principle and technology parameters, is described.───叙述了异型铸件立式离心铸造的工艺, 其中包括设计原则和工艺参数.

The centrifugal casting process of high aluminum - zinc alloys was investigated through products.───结合产品试验了高铝锌基合金的离心铸造工艺.

The development process and status, and further research directions of FGMs by centrifugal casting are comprehensively discussed in this paper.───本文对离心铸造法制备梯度功能材料的发展过程、研究现状及今后研究的方向进行了综合评述。

The effects of mischmetal addition on the microstructure in centrifugal casting lead bronze hare been studied.───研究了混合稀土对离心铸造铅青铜组织的影响.

Based on rapid prototyping technology the silicon rubber mold for centrifugal casting is conveniently made.───硅橡胶模离心浇注装置结构简单,投资少.

These rolls can be produced by static casting or centrifugal casting.───可采用静态铸造或离心铸造生产.

A new type of centrifugal casting coating was introduced and its relative performances were tested.───介绍了一种新的离心铸造用涂料的配制,测定了其有关性能.

The corresponding measures should be adopted on raw material management, hot metal melting and centrifugal casting.───相应的应从原材料管理, 铁水熔炼,离心铸造上采取控制措施.

A number of practical patent coatings for centrifugal casting pipe are listed in this paper.───文中列出大量实用的离心铸管涂料专利配方.

unsaturated polyester resin is designed for centrifugal casting molding glass pipe (HOBAS pipe) design of the structure layer resin is a low viscosity, medium reactivity of o-benzene resin.───不饱和聚酯树脂是专门为离心浇铸成型玻璃钢管道(HOBAS管)设计的结构层树脂，是低粘度，中等反应性的邻苯型树脂。

The two motor driving rollers of the centrifugal casting machine must keep synchronous and keep load balance.

The Electromagnetic levitation melt centrifugal casting(ELCC)technology for preparing the low cost high quality silicon solar cell paves a new way for reducing the production cost of the solar cell.

This paper introduced that horizontal centrifugal casting technology is used to develop the composite acicular spheroidal graphite cast iron collar for tension reducing mill of Baogang pipe mill.

One of keys of production of centrifugal casting pipe of s. g. iron is continuous and fast delivery of qualified base iron with proper chemical composition and temperature.

The technology of grinding ball by centrifugal casting, the rotational speed, the method for calculation of ingate area and factors influencing technological process were introduced.

The shortcomings of horizontal centrifugal casting machine are analyzed, and a vertical casting unit in structure of double-layered hollow abdomen is designed.

The influence of rotating speed of centrifugal casting machine on the semi-solid microstructure of Al-Si alloy was researched.

In the light of application to centrifugal casting machine, working principle of soft starter is analyzed and the advantage of this new energy-saving technique of soft starter is presented.

Some aspects in cast-iron drainpipe production in centrifugal casting, such as machine type, influence of coating, formation of pit and pin-hole defects, were analyzed and approached.